Single hung
Double hung
Horizontal roller
Casement
Bay & bow
Sliding glass doors
Entry doors
Impact garage doors
PGT
CGIFree in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Get your free estimateCGI Door Installation in Henderson: What to Know First
CGI door installation in Henderson typically runs $1,450 to $4,800 for a single entry door, depending on series, size, and whether the rough opening needs work. Most single-door installs are finished in one visit; French and double doors usually take a full day. We’re an independent CGI service provider, so our quote reflects the actual labor and materials for your opening, not a manufacturer-mandated price sheet.
This page is for Henderson homeowners who already have a CGI door, or who’ve decided on a CGI line and want it set correctly the first time. If the frame is out of true, the door will bind by July and you’ll be calling someone else next spring. Call (833) 842-6670 for a free estimate.
How CGI Products Fail – and How We Fix Them
CGI builds to a price point, and the doors that show up in Henderson homes tend to fail in predictable places. Here’s what our technicians see, and what we do about it.
- CGI Steel Entry Doors – frame deflection at the strike jamb. The steel skin is rigid, but the frame can flex under the deadbolt load, especially on a door facing west into afternoon sun. You get a deadbolt that turns hard by August and a door that won’t latch unless you lift it. We shim and re-anchor the jamb, then reset the strike plate to the actual swing.
- CGI fiberglass entry doors – delamination at the bottom rail. Henderson’s monsoon season pushes water against the sill, and if the threshold isn’t bedded and back-dammed properly, the bottom rail wicks moisture and the skin lifts. We pull the slab, dry it, seal the bottom edge, and reset with a proper sill pan.
- Hurricane-rated CGI doors – gasket compression loss. The impact-rated lines carry a full-perimeter gasket, and after a few summers of 110-degree heat, that gasket flattens and the door stops sealing. Most homeowners don’t notice until the dust comes in. We replace the gasket with the correct durometer spec for the series, not a generic strip from the hardware aisle.
- CGI French and double doors – astragal misalignment. The inactive leaf drifts out of plumb over time, and the astragal stops meeting the active leaf cleanly. That’s usually a hinge-side anchor issue, not the door. We reset both leaves and re-hang to a common plane before touching the astragal.
- CGI sliding patio doors – roller track wear. The bottom track fills with Henderson grit and the rollers flat-spot, so the panel drags and eventually jumps track. We pull the panel, replace rollers with OEM-spec units, clean and re-level the track.
Styles & brands we work with
- Single hung
- Double hung
- Horizontal roller
- Casement
- Bay & bow
- Sliding glass doors
- Entry doors
- Impact garage doors
- PGT
- CGI
Our CGI Door Installation Process
- 1
Phone call and scheduling. A live person answers every call, day or night. We book a time, confirm the CGI series if you know it, and tell you what to expect.
- 2
On-site measurement and diagnostics. Our background-checked, uniformed technician measures the rough opening twice, checks plumb and level, and confirms the door is out of true before we touch anything. We photograph the opening and the existing hardware.
- 3
Parts decision, on paper. If a part is needed, we quote OEM versus a quality aftermarket equivalent side by side, with the trade-offs stated. You pick. No surprise line items later.
- 4
Installation. We set, shim, and anchor to the actual opening, not the spec sheet. Threshold gets bedded and back-dammed. Hardware gets aligned to the swing.
- 5
The test. Door opens and closes on a light push, deadbolt throws clean, no daylight at the perimeter, no drag through the full swing. We don’t call it done until it passes.
- 6
Warranty registration and cleanup. Under The Keystone Standard, both manufacturer warranty layers are registered in writing with durations stated before we leave. Then the site gets swept and hauled.
See the difference
Before
After
Before
After
Before
AfterWhat CGI Door Installation Costs in Henderson
| Scenario | Typical Range |
|---|---|
| Single entry door, standard opening, CGI fiberglass or steel | $1,450 – $2,600 |
| Hurricane-rated entry door with impact glazing | $2,200 – $3,900 |
| French or double door, paired leaves | $2,800 – $4,800 |
| Sliding patio door replacement | $1,900 – $3,600 |
| Rough opening repair or reframing | $250 – $900 additional |
What moves the price: door size and series, impact-rating requirements, whether the existing opening was framed true, and hardware. Henderson homes built in the 1990s and early 2000s often need jamb repair because the original opening was never shimmed to spec. Call (833) 842-6670 for a free estimate – the quote is line-item and it doesn’t move once work starts.
Why Henderson Homeowners Call TruePane Windows & Doors Henderson for CGI Work
We’re an authorized installer for more than a dozen manufacturer lines, including Andersen, Pella, Marvin, Milgard, PGT, and CGI. On a CGI job that matters less than what happens after: the 90-Day Done Right Promise means if the door binds in July, we come back and make it right. No paperwork fight, no fine print that covers neither.
Every job starts with a technician who has up to 18 years of experience and who measures the opening twice. We also service PGT, CWS, ES Windows, and ECO Window Systems, so if a CGI part is backordered, we can talk through alternatives on paper. And a live person answers the phone 24 hours a day, 7 days a week. We plan to be in Henderson for a long time yet.
FAQs
Only if the door is installed incorrectly or with non-spec parts. Under The Keystone Standard, we register both manufacturer warranty layers in writing with durations stated before we leave, so the coverage is documented and not dependent on memory.
Yes for most common series – entry doors, patio sliders, French doors. OEM parts for older or discontinued lines can carry lead times, so we quote OEM versus a quality aftermarket equivalent side by side and let you decide. Call (833) 842-6670 for a parts check.
If the slab and frame are sound and the problem is hardware, gaskets, or alignment, repair is almost always the right call. If the bottom rail has delaminated from water intrusion or the frame is out of true beyond shimming, replacement makes more sense. We’ll tell you which on the estimate, in writing.
A single entry door is typically one visit, most of a day. French and double doors usually run a full day. If reframing is needed, we’ll say so up front and quote the additional time.
Yes – PGT, CWS, ES Windows, and ECO Window Systems among others. We’re an independent CGI service provider, not affiliated with or authorized by CGI, so our advice reflects the door in front of us rather than a manufacturer playbook.
Call TruePane Windows & Doors Henderson at (833) 842-6670 for a free estimate on your CGI door. A live person answers every call, the quote is line-item on paper, and if the pane is not true, the job is not done.
Written by the team at TruePane Windows & Doors Henderson, serving Henderson and nearby areas.