Single hung
Double hung
Horizontal roller
Casement
Bay & bow
Sliding glass doors
Entry doors
Impact garage doors
PGT
CGIFree in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Get your free estimateTherma-Tru Door Installation in Henderson: What to Know First
We install Therma-Tru entry, French, double, storm, and exterior doors for Henderson homeowners as an independent Therma-Tru service provider. Most single-door replacements are measured, quoted, and set in one visit, with double doors and sidelight configurations usually taking two. We won’t hand you the lowest number in the valley and then add line items once the old door is out – the quote is the bill, in writing.
This page is for the owner of a Therma-Tru door – the Fiber-Classic or Smooth-Star entry that’s been in the wall fifteen years, the Classic-Craft that’s starting to show at the sill – who wants it replaced or reset by people who know the product. If that’s you, call (833) 842-6670 and a live person will pick up.
How Therma-Tru Products Fail – and How We Fix Them
Therma-Tru builds a good door. What fails in Henderson is rarely the slab itself – it’s the install, the seal, and the desert working on both. These are the calls we run most often, and what we do about each.
- Sill rot and water staining on Fiber-Classic and Smooth-Star entries. The composite slab holds up; the wood or MDF sill beneath it doesn’t, especially on north- and west-facing doors where sprinkler overspray sits. We pull the door, replace the sill with a composite or aluminum sill pan, and re-flash the threshold so water sheds instead of pooling. A sill that’s soft underfoot means the pan was never right.
- Warping and binding on west-facing doors. Henderson afternoons push past 110°F, and a west-facing Therma-Tru in a dark finish absorbs enough heat to move. Doors that swing free in January drag on the strike side by July. We check the frame for plumb and the hinge side for shim compression, reset the frame, and confirm the door is hung true before we call it done.
- Failed weatherstrip and sweep on Classic-Craft and Fiber-Classic lines. The kerf weatherstrip and door bottom sweep take the sun and dry out faster here than the manufacturer’s replacement intervals suggest. We replace with OEM Therma-Tru kerf seal where it’s available and a quality aftermarket sweep when it isn’t, then test the door against a light gap.
- Delamination and finish failure on fiberglass skins. When a Fiber-Classic or Smooth-Star skin blisters at the bottom rail, it’s usually moisture that got behind a failed paint edge or a bad threshold seal. We replace the slab rather than patch it, because a re-skinned door fails again.
- Loose hinges and sagging on heavy double-door and French configurations. Therma-Tru French and double doors are heavy, and a frame shimmed short on the hinge side lets the active leaf sag and the astragal gap. We re-shim and re-hang, or install a fresh frame with the door weight carried properly.
Styles & brands we work with
- Single hung
- Double hung
- Horizontal roller
- Casement
- Bay & bow
- Sliding glass doors
- Entry doors
- Impact garage doors
- PGT
- CGI
Our Therma-Tru Door Installation Process
- 1
Measure and diagnose. We measure every opening twice, check the existing frame for plumb and square, and look at the sill, flashing, and wall for the real cause of whatever brought you to call. No guessing on a door.
- 2
Side-by-side quote on paper. We show you Therma-Tru lines and alternatives from the brands we install – PGT, CGI, CWS, ES Windows and others – with the price of each in writing, so you see exactly what you’re buying before you commit.
- 3
Parts decision, made openly. OEM Therma-Tru hardware, sills, and weatherstrip where they fit and are available; a quality aftermarket part only when it’s the better call, and we tell you which we’re using and why.
- 4
The install. Old door out, opening cleaned and prepped, new door set level in a properly shimmed and flashed frame. Background-checked, uniformed technicians, working in your home the way they’d work in their own mother’s.
- 5
Test and adjust. We open, close, and latch the door through a full swing, check the seal against a light gap, and adjust the strike and hinges until it operates the way it should.
- 6
Register the warranty, in writing. Both manufacturer warranty layers registered and durations stated before we leave – The Keystone Standard. Then cleanup, and the 90-Day Done Right Promise behind the work.
See the difference
Before
After
Before
After
Before
AfterWhat Therma-Tru Door Installation Costs in Henderson
These are the ranges we see on Therma-Tru work in Henderson. Your quote is the number, not an estimate that grows.
| Job | Typical range |
|---|---|
| Single Therma-Tru entry door replacement (standard size) | $1,400 – $3,200 installed |
| Therma-Tru French or double door set | $3,000 – $6,500 installed |
| Entry door with sidelights | $2,600 – $5,200 installed |
| Sill, threshold, and flashing rebuild only | $450 – $1,100 |
| Weatherstrip, sweep, and hardware replacement | $180 – $420 |
What moves the price: door width and configuration, glass options, whether the frame and flashing need rebuilding, and hardware finish. Call (833) 842-6670 – estimates are free, and the quote is itemized line by line.
Why Henderson Homeowners Call TruePane Windows & Doors Henderson for Therma-Tru Work
We’ve been part of this community for over 42 years, and our technicians have up to 18 years of experience on doors and windows. Every Therma-Tru job carries the 90-Day Done Right Promise and The Keystone Standard: both manufacturer warranty layers registered in writing, durations stated, no arguing. We’re an independent Therma-Tru service provider, and we also install and service PGT, CGI, CWS, and ES Windows – so if a Therma-Tru line isn’t the right fit for your opening, you’ll hear it from us on paper.
A live person answers the phone 24 hours a day, seven days a week. We show up when we say, and if the pane is not true, the job is not done.
FAQs
Not if the install is done to Therma-Tru’s spec and the warranty is registered correctly – that’s exactly why we register both warranty layers in writing before we leave. A correctly installed door keeps its coverage; a shortcut install is where warranties go void. Call (833) 842-6670 to talk through your specific door.
Usually, yes – OEM sills, weatherstrip, and hardware are generally available for current and recent Therma-Tru lines, and we tell you up front when a part is no longer made. In that case we use a quality aftermarket equivalent and say so on the quote. Call (833) 842-6670 with your model and we’ll check.
If the slab is sound and the problem is the sill, seal, or frame, repair is worth it. If the fiberglass skin is delaminated or the frame is out of square, replacement is the honest call. We diagnose the actual failure before quoting either, so you’re not sold a new door for a sill problem.
A single entry door is typically a one-visit job; French and double door sets usually take two. Weather, glass options, and frame repairs can add time, and we tell you the schedule in writing before we start.
Yes – storm doors and exterior Therma-Tru configurations are part of what we install. Call (833) 842-6670 to schedule a free estimate.
Ready to get the door done right? Call TruePane Windows & Doors Henderson at (833) 842-6670 for a free estimate. We’ll measure your opening, quote the Therma-Tru lines and alternatives side by side on paper, and stand behind the work in writing. A live person answers, day or night.
Written by the team at TruePane Windows & Doors Henderson, serving Henderson and nearby areas.