A TruePane company - serving Henderson, NV

CGI Door Installation in Henderson, NV

Single hungSingle hung
Double hungDouble hung
Horizontal rollerHorizontal roller
CasementCasement
Bay & bowBay & bow
Sliding glass doorsSliding glass doors
Entry doorsEntry doors
Impact garage doorsImpact garage doors
PGTPGT
CGICGI
Every visit starts with

Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style

Get your free estimate

CGI Door Installation in Henderson: What to Know First

CGI door installation in Henderson typically runs $1,450 to $4,800 for a single entry door, depending on series, size, and whether the rough opening needs work. Most single-door installs are finished in one visit; French and double doors usually take a full day. We’re an independent CGI service provider, so our quote reflects the actual labor and materials for your opening, not a manufacturer-mandated price sheet.

Call (833) 842-6670

This page is for Henderson homeowners who already have a CGI door, or who’ve decided on a CGI line and want it set correctly the first time. If the frame is out of true, the door will bind by July and you’ll be calling someone else next spring. Call (833) 842-6670 for a free estimate.

How CGI Products Fail – and How We Fix Them

CGI builds to a price point, and the doors that show up in Henderson homes tend to fail in predictable places. Here’s what our technicians see, and what we do about it.

  • CGI Steel Entry Doors – frame deflection at the strike jamb. The steel skin is rigid, but the frame can flex under the deadbolt load, especially on a door facing west into afternoon sun. You get a deadbolt that turns hard by August and a door that won’t latch unless you lift it. We shim and re-anchor the jamb, then reset the strike plate to the actual swing.
  • CGI fiberglass entry doors – delamination at the bottom rail. Henderson’s monsoon season pushes water against the sill, and if the threshold isn’t bedded and back-dammed properly, the bottom rail wicks moisture and the skin lifts. We pull the slab, dry it, seal the bottom edge, and reset with a proper sill pan.
  • Hurricane-rated CGI doors – gasket compression loss. The impact-rated lines carry a full-perimeter gasket, and after a few summers of 110-degree heat, that gasket flattens and the door stops sealing. Most homeowners don’t notice until the dust comes in. We replace the gasket with the correct durometer spec for the series, not a generic strip from the hardware aisle.
  • CGI French and double doors – astragal misalignment. The inactive leaf drifts out of plumb over time, and the astragal stops meeting the active leaf cleanly. That’s usually a hinge-side anchor issue, not the door. We reset both leaves and re-hang to a common plane before touching the astragal.
  • CGI sliding patio doors – roller track wear. The bottom track fills with Henderson grit and the rollers flat-spot, so the panel drags and eventually jumps track. We pull the panel, replace rollers with OEM-spec units, clean and re-level the track.
Explore

Styles & brands we work with

  • Single hung
  • Double hung
  • Horizontal roller
  • Casement
  • Bay & bow
  • Sliding glass doors
  • Entry doors
  • Impact garage doors
  • PGT
  • CGI

Our CGI Door Installation Process

  1. 1
    Phone call and scheduling. A live person answers every call, day or night. We book a time, confirm the CGI series if you know it, and tell you what to expect.
  2. 2
    On-site measurement and diagnostics. Our background-checked, uniformed technician measures the rough opening twice, checks plumb and level, and confirms the door is out of true before we touch anything. We photograph the opening and the existing hardware.
  3. 3
    Parts decision, on paper. If a part is needed, we quote OEM versus a quality aftermarket equivalent side by side, with the trade-offs stated. You pick. No surprise line items later.
  4. 4
    Installation. We set, shim, and anchor to the actual opening, not the spec sheet. Threshold gets bedded and back-dammed. Hardware gets aligned to the swing.
  5. 5
    The test. Door opens and closes on a light push, deadbolt throws clean, no daylight at the perimeter, no drag through the full swing. We don’t call it done until it passes.
  6. 6
    Warranty registration and cleanup. Under The Keystone Standard, both manufacturer warranty layers are registered in writing with durations stated before we leave. Then the site gets swept and hauled.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

What CGI Door Installation Costs in Henderson

Scenario Typical Range
Single entry door, standard opening, CGI fiberglass or steel $1,450 – $2,600
Hurricane-rated entry door with impact glazing $2,200 – $3,900
French or double door, paired leaves $2,800 – $4,800
Sliding patio door replacement $1,900 – $3,600
Rough opening repair or reframing $250 – $900 additional

What moves the price: door size and series, impact-rating requirements, whether the existing opening was framed true, and hardware. Henderson homes built in the 1990s and early 2000s often need jamb repair because the original opening was never shimmed to spec. Call (833) 842-6670 for a free estimate – the quote is line-item and it doesn’t move once work starts.

Why Henderson Homeowners Call TruePane Windows & Doors Henderson for CGI Work

We’re an authorized installer for more than a dozen manufacturer lines, including Andersen, Pella, Marvin, Milgard, PGT, and CGI. On a CGI job that matters less than what happens after: the 90-Day Done Right Promise means if the door binds in July, we come back and make it right. No paperwork fight, no fine print that covers neither.

Every job starts with a technician who has up to 18 years of experience and who measures the opening twice. We also service PGT, CWS, ES Windows, and ECO Window Systems, so if a CGI part is backordered, we can talk through alternatives on paper. And a live person answers the phone 24 hours a day, 7 days a week. We plan to be in Henderson for a long time yet.

FAQs

Need Windows & Doors help nationwide? Licensed & insured · free written estimates
Call (833) 842-6670
Local Service Coverage

Request a Free Estimate in Henderson

Tell us what you need - TruePane Windows & Doors Henderson responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Call Now - 24/7 Dispatch