A TruePane company - serving Henderson, NV

CGI Impact Garage Doors in Henderson, NV

Impact garage doorsImpact garage doors
Single hungSingle hung
Double hungDouble hung
Horizontal rollerHorizontal roller
CasementCasement
Bay & bowBay & bow
Sliding glass doorsSliding glass doors
Entry doorsEntry doors
PGTPGT
CGICGI
Every visit starts with

Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style

Get your free estimate

CGI Impact Garage Doors: The Henderson Owner’s Guide

We install CGI impact garage doors and matched replacement components for Henderson homeowners, with typical whole-door installed pricing running roughly $2,900 to $7,400 depending on size, wind-load rating, and whether a new opener and reinforcement are needed. Because impact doors are built to a different standard than standard doors, most owners discover a problem the same way: the door gets heavy on one side, the panels start to look wavy in the afternoon sun, or the opener strains and reverses halfway down. In Henderson, that pattern usually shows up in late spring and again in October, when the desert swing between cool mornings and 100-degree afternoons works the seals and hardware hardest. We quote the door and the parts on paper so you can see exactly what you’re buying before anyone touches the tracks.

Call (833) 842-6670

Which CGI Models This Applies To

CGI makes a wide range of impact-rated residential doors through its Hurricane and wind-load series, and the parts inside them are not interchangeable across every line. The single biggest compatibility gotcha we run into in Henderson is panel and section fit: two CGI impact doors that look identical from the curb can use different track gauges, different hinge patterns, and different bottom seal profiles depending on which series was spec’d for the original build. A part pulled for one will not seat correctly on the other no matter how careful the install.

Here’s how to identify what you actually have before ordering anything:

  • Look for the CGI data label on the inside of the door or on the jamb, which lists the model, series, and wind-load rating.
  • Measure the opening width and height, plus the thickness of each panel, since impact doors run heavier than standard.
  • Note the track gauge and the bottom-seal profile, which are the two parts most often mismatched.

On the OEM-versus-aftermarket question, we’re straight with Henderson homeowners: for hinges, rollers, bottom seals, and weatherstripping, a quality aftermarket equivalent is often the square deal and performs as well as the original. For structural impact components, the reinforced struts and the door itself, we quote OEM so the wind-load rating on the label stays valid.

Explore

Styles & brands we work with

  • Single hung
  • Double hung
  • Horizontal roller
  • Casement
  • Bay & bow
  • Sliding glass doors
  • Entry doors
  • Impact garage doors
  • PGT
  • CGI

Signs Your CGI Impact Garage Door Is Failing

Impact doors are heavier and stiffer than standard doors, so their failure modes look a little different. Here are the five we see most in Henderson, and what each one is telling you:

  • The door sags or binds on one side. Worn hinges or a track that’s drifted out of plumb. The extra weight of an impact door punishes tired hardware faster than a standard door would.
  • Panels look wavy or the door bows in the middle. Heat and weight stress on the sections, sometimes a sign a reinforcement strut was never added or has loosened. Southern Nevada summers accelerate this.
  • The opener strains, reverses, or the door won’t close fully. The spring tension or the opener’s force setting can’t handle the door’s weight anymore. On impact doors this often means the springs are near end of life.
  • Daylight or heat leaking around the edges. A flattened bottom seal or worn perimeter weatherstripping. In Henderson that shows up as a hotter garage and higher cooling bills before you notice the gap.
  • Loud grinding or a door that shudders on the way up. Dry or failed rollers and worn track. Left alone, this wears the door’s hinges and the opener’s drive gear.

Any one of these is worth a look. Two or more together usually means the door needs a full inspection, not just one part.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Here’s the honest range for Henderson, installed, priced by the job rather than the part alone:

Work Typical Installed Range
Bottom seal / weatherstripping replacement $180 – $340
Hinge, roller, and hardware refresh $220 – $480
Track realignment or section replacement $350 – $850
Full CGI impact door replacement (installed) $2,900 – $7,400

The range is driven by door size, wind-load rating, panel configuration, and whether the opener and reinforcement need updating. We quote parts and labor separately on paper so there are no surprise line items on the bill. Every job is covered by the 90-Day Done Right Promise, with both manufacturer warranty layers registered in writing and durations stated before we leave. Most repairs are done in a single visit.

DIY or Call Us?

You can safely check a few things yourself: listen for grinding, look for daylight around the edges, watch whether the door binds on one side, and read the CGI data label on the jamb. Those checks tell us a lot and cost nothing.

What we don’t recommend is adjusting the torsion springs or the high-tension cables on an impact door. These are under heavy load, and an impact door’s extra weight means more stored energy than a standard door. A spring that lets go can cause serious injury, and it’s genuinely a job for a trained technician, not a Saturday project. Replacing a bottom seal or weatherstripping is within reach for a careful homeowner. The moment a door sags, bows, or fights the opener, it’s time to call. Call (833) 842-6670 for a free estimate and we’ll tell you plainly whether it’s a repair or a replacement.

FAQs

How long do CGI impact garage doors and their parts last in Henderson? A quality impact door typically lasts 15 to 25 years, with hardware like hinges, rollers, and seals needing attention every 5 to 10 years. Henderson’s heat and dry air wear seals and weatherstripping faster than milder climates, so we check those at every visit. Call (833) 842-6670 for an inspection and exact pricing.

Can it be repaired instead of replaced? Often, yes. A single failed section, worn hardware, or a leaking seal can usually be repaired, and we’ll tell you honestly when repair is the square deal and when the door is far enough along that replacement makes more sense. Call (833) 842-6670 to schedule a free estimate.

How long does the swap take? Hardware and seal repairs are typically done in a single visit, often within a couple of hours. A full door replacement is usually a one-day job, barring special order timing or permit requirements. Call (833) 842-6670 and we’ll give you a realistic window.

How do you source the right CGI part? We pull the model and series from your door’s data label, match it to a manufacturer line we install, and quote OEM or a quality aftermarket equivalent side by side on paper. TruePane Windows & Doors Henderson is an independent service provider and is not affiliated with CGI. We’re an authorized installer for more than a dozen lines, including Andersen, Pella, Marvin, Milgard, PGT, CGI, and ES Windows, so you see exactly what you’re buying.

When a CGI impact garage door starts to sag, seal poorly, or fight the opener, the fix starts with an honest look at the whole door and a quote on paper. Call TruePane Windows & Doors Henderson at (833) 842-6670 for a free estimate. We’ll be there when we say, with background-checked, uniformed technicians, upfront pricing, and the 90-Day Done Right Promise behind every job. If the pane is not true, the job is not done.

Written by the team at TruePane Windows & Doors Henderson, serving Henderson and nearby areas.

Need Windows & Doors help nationwide? Licensed & insured · free written estimates
Call (833) 842-6670
Local Service Coverage

Request a Free Estimate in Henderson

Tell us what you need - TruePane Windows & Doors Henderson responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Call Now - 24/7 Dispatch