A TruePane company - serving Henderson, NV
C

CWS Impact Garage Doors in Henderson, NV

Impact garage doorsImpact garage doors
Single hungSingle hung
Double hungDouble hung
Horizontal rollerHorizontal roller
CasementCasement
Bay & bowBay & bow
Sliding glass doorsSliding glass doors
Entry doorsEntry doors
PGTPGT
CGICGI
Every visit starts with

Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style

Get your free estimate

CWS Impact Garage Doors: The Henderson Owner’s Guide

We install and service CWS-compatible impact garage doors in Henderson, and a full door replacement for a CWS impact door typically runs about $2,400-$5,800 depending on size and wind-load rating. Individual part repairs, like a failed roller, hinge, or torsion spring, usually land between $150 and $420. We’re an independent service provider and not affiliated with CWS, so we match your existing door to the correct part by model and measurement, not by logo alone.

Call (833) 842-6670

Most Henderson owners find out something has failed the same way. The door stops sitting flush against the opening, it binds halfway up, or the automatic reverse kicks in before the door meets the floor. In our experience, that noise and drag almost always traces back to worn rollers, a stretched torsion spring, or a bent track after a hard summer. The wind-load requirement that makes CWS impact doors work so well can also mask a failing part until it finally gives.

Which CWS Models This Applies To

CWS builds impact-rated garage doors across several series, and the part you need depends on the series, the panel width, and the wind-load rating stamped on the door. Look for the manufacturer label inside the door frame or on the edge of a top panel. That label usually carries the model number and a wind-load pressure rating, often in the range of +30 to -50 psf depending on whether the door is rated for the local wind zone. The label is the single best clue before we measure.

Here’s a compatibility detail that trips people up in the field: CWS impact doors frequently use reinforced hinges and heavier-gauge torsion hardware than a standard door of the same width. A generic hinge or an undersized spring that fits a non-impact door often won’t hold on a CWS impact panel. When we quote, we show you the OEM part alongside a quality aftermarket equivalent so you can see the spec difference on paper. We don’t stock parts and we don’t carry them on a truck. We measure, source the correct part for your model, and return to install it.

Explore

Styles & brands we work with

  • Single hung
  • Double hung
  • Horizontal roller
  • Casement
  • Bay & bow
  • Sliding glass doors
  • Entry doors
  • Impact garage doors
  • PGT
  • CGI

Signs Your CWS Impact Garage Doors Is Failing

  • The door binds or jerks going up. Worn or flat-spotted rollers are usually the cause, and left alone they chew into the track and stress the springs.
  • It reverses before it reaches the floor. A misadjusted safety sensor or a track out of alignment is the common culprit; it’s worth checking before it becomes a stuck-door call.
  • A loud bang, then the door won’t lift. That’s a broken torsion spring, the most dangerous failure on the door, and it needs a trained technician.
  • Uneven gaps at the bottom or sticking in July. Heat expansion and a warped or worn bottom seal show up on Henderson doors every summer, and the seal or the panel is the place to look.
  • Grinding or a bent track after a hard bump. Track damage on an impact door can compromise the wind rating, so it should be inspected rather than straightened by hand.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Replacement costs in Henderson break down by what’s actually failing, and we quote parts and labor on the same written line-item so there’s no surprise on the bill.

Part or job Typical installed range
Rollers (set of 10) $150-$260
Hinges (per set) $120-$220
Torsion spring replacement $220-$420
Track repair or replace $180-$380
Full CWS impact door replacement $2,400-$5,800

What drives the range is the part spec, the door width, and whether a wind-rated torsion setup needs re-tuning. Every job carries the 90-Day Done Right Promise on our workmanship, and The Keystone Standard means the warranty terms are put in writing before we leave. We’ll show you the part we’re installing and why it matches your door.

DIY or Call Us?

You can safely check a few things yourself: look for the model label, watch whether the door runs straight, and test the reverse feature with a piece of wood under the door. What you should not touch is the torsion spring or the cable system. Those parts are under extreme tension, and a spring that lets go can cause serious injury, which is why we send a trained technician for anything involving the spring, cable, or bottom bracket. Most of what goes wrong on a Henderson impact door is straightforward to fix once the right part is in hand. Call (833) 842-6670 and we’ll tell you what’s worth checking and what should be left to us.

FAQs

How long do CWS impact garage door parts last? Rollers and seals typically wear out in three to seven years under regular use, while a quality torsion spring can last much longer but cycles and heat shorten its life. Henderson summers are hard on seals and finish, so we check both when we’re on site.

Can the part be repaired instead of replaced? Often, yes. A single worn roller, a bent hinge, or a misaligned track can be repaired without a full replacement, and we’ll tell you honestly when a repair will hold and when it won’t. Call (833) 842-6670 for a straight answer.

How long does the swap take? A roller, hinge, or seal swap is usually a short visit, while a torsion spring replacement or track work takes longer because we re-tune the door afterward. We’ll give you a time window when we quote. Call (833) 842-6670 to schedule.

How do you source the part for my CWS door? We read your door’s model label, measure the opening and the hardware, and source the correct part for your series, showing the OEM and the aftermarket pick side by side on paper. We don’t stock parts; we order what your door needs. Call (833) 842-6670 for a free quote.

We also service PGT, CGI, and ES Windows doors for Henderson homeowners. If you’re not sure which brand you have, we’ll identify it when we arrive.

Whether it’s a single failed part or a full impact door replacement, we’ll get you the right part, quote it on paper, and stand behind the work. Call (833) 842-6670 for a free estimate in Henderson today.

Written by the team at TruePane Windows & Doors Henderson, serving Henderson and nearby areas.

Need Windows & Doors help nationwide? Licensed & insured · free written estimates
Call (833) 842-6670
Local Service Coverage

Request a Free Estimate in Henderson

Tell us what you need - TruePane Windows & Doors Henderson responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Call Now - 24/7 Dispatch